Jump to content

churchy

RHOCaR Member
  • Posts

    48
  • Joined

  • Last visited

About churchy

  • Birthday 04/19/1964

Previous Fields

  • Car type
    robin hood s7
  • Full name
    andy church

Profile Information

  • Gender
    Male
  • Location
    camb's

Recent Profile Visitors

4,378 profile views

churchy's Achievements

Builder

Builder (2/6)

7

Reputation

  1. Thank you guys, it is great to know what I have to do and I best way to tackle it, the pictures are great and it just goes to show how important this club is, the wealth of knowledge and everyone's willing to give advice is tremendous and I am so grateful. I will keep you up to date with my progress and thank you again
  2. Thank you guys, so once I have removed the nuts the threaded bar should knock out, then once removed the tube with the bushes should lift out so I can get to the bushes if I understand correctly
  3. Hi guys, need some advice before tackling my next job. On the drivers side I have about 1/4" play on this bush at the back that I have circled in pink, now I think there is a Bush the other side of this threaded bar/ bolt, it looks like it doesn't travel all the way through so another bush on the front, has anybody tackled this job and what is on the other side that I cannot see, my last question is how do I get in to repair, amy advise would be very appreciated. Thanks Andy
  4. churchy

    oil cooler

    Silly question but have you tried the car without the bonnet and nose cone off to see if the car still overheats, if it does then I think there could be something causing the problem but if it's fine then it could well be not getting enough air directed through the rad
  5. churchy

    oil cooler

    Is your rad sitting upright so the air is hitting it straight on and did you have this problem before the engine was removed
  6. churchy

    oil cooler

    I run a 2 litre pinto and had overheating problems a few years ago and the previous owner had removed the thermostat, I found out after trial and error that my radiator just wasn't getting enough air flow through it. I put a double core rad in which increased cooling capacity and then a electric fan but made sure that when the fan ran it pull air across the whole of the rad and the car now runs lovely with a thermostat back in even in traffic, to me if the thermostat is missing this has been an on going problem, also at the same time as my cooling problems i changed my volt meter for an oil temp gauge which I think is far more benifical, I noticed my oil temp was high especially when I was high revving the car, I do have a sump guard fitted but i did fit an air to air oil cooler in front of my rad, ran it from my oil filter with an thermostatic sandwich plate so not to cool the oil too much as this is worst than getting it too high, I had to change my oil filter for an cosworth filter, it passes the same oil rate and is ok with 20/50 oil but is smaller in length so it would fit inside my engine bay. The filter came from Burton and is a EFL298 FILTER this did bring my oil temp down and now it is happy days. Hope this helps Andy
  7. Hi, I have a Sierra base S7 and this is about the only job I have been putting off for some time. The rear suspension, at the moment I am running is a Sierra set up with standard Sierra shock absorbers(new) with springs inboard on the rear subframe these springs are not standard but I have no idea what they are. I love the ride height of the set up at the moment and the wheels sit nicely filling the wheel arch but when riding along the rear is too soft and over pot holes and large bumps the suspension bottoms out . My question is what's the best way to sort this out with keeping the ride height the same and not going too hard, any advise will be gladly appreciate. Cheers Andy
  8. Thankyou guys, for that information and as usual it is a great help to me. I have just sworn my motor and will be doing the rear first. Thankyou Pete for the offer of your spear springs and i may take you up on that when I come to the fronts but i will let you know if that is ok. Thankyou guys once again for your time and help cheers
  9. Thankyou guys. It always amazes me the knowledge from the owners club and that is worth the membership fee in itself. Thankyou again, now I know what I will be looking and asking for. Cheers again Andy
  10. Hi, my winter project is to change the rear and front suspension, i have the rear suspension covered but the front I need a bit of advice on. I have a sierra base S7 with in board spax adjustable coil overs that came in the kit I would think, I want to keep with the in board adjustable coil overs but i think the the springs are a little to hard but do not know what spring rate is fitted but more importantly what springs and shocks should I get and where to get them, i love the ride but just think a softer spring would be better without going to soft. Any advice would be grateful especially from anybody who has changed there shocks with this set up. Cheers Andy
  11. Hi, in the end I took engine, gearbox and then prop out. Took the prop to Morris Bailey who made a updated prop in 24 hours and while I had the engine out i put a Kent cam fast road cam kit, a Kent Vernier pulley and lighten the fly wheel on my pinto. The car has been back on the road for 2 weeks and what a difference the upgrades had made it is almost like a different car the engine sounds different but it also spins up so much quicker and the cam doesn't slow the car down at low revs at all but when i put my foot down the car is so much quicker and more enjoyable. Thanks for all the advice and as always that advise has lead me to look in the right place, i think it is always nice to hear how our topics end. Once again thankyou guys
  12. Thankyou guys for the advice even if it's not what I want to hear but thought that would be the answere. Two questions engine and gearbox out together or can I strip them out separately as last time I took the engine out there wasn't much room and i don't know weather both will come out together in one. As for the mot then yes I suppose he should of seen it. Thankyou guys for the advice as always it is much appreciated. Cheers Andy
  13. Thankyou guys for the advise looked under car today and the prop uj has gone, which is nice to know that with your help I have traced the problem. Now to the downside is i cannot remove the prop as it is hitting the diff? I have a S7 and the floor is one sheet stainless and removing the tunnel is not an option. So has anyone done this job in the pass, is it drive shafts out and rear diff removed or can I cut the floor to allow a small access panel to assist with dropping the prop enough to pass the diff my only worry with last option sealing the structure any advise would be every helpful. Cheers Andy
  14. Thanks nigel i was going to check that as well but at moment I have a big so crawling underneath the car is the last thing on my mind, when I am checking my prop uj I should notice a play with the prop in place just by turning it or does the prop has to come out and if so with the prop out could I run the engine and gearbox slowing to eliminate those too. Thanks for the advice and i will let you know what I find next week when feeling a bit better. As always the club's knowledge and advise is first class. Cheers Andy
  15. No, the prop goes straight into the gearbox, if I get time i shall remove prop and check ug' s but thanks for the advice. Any advice welcome. Cheers Andy
×
×
  • Create New...