Engine
Won't fire, won't even turn? Not running smooth? Cutting out? Ask here!
6,152 topics in this forum
-
Hi All I am currently putting a set of webber 40s onto a standard 2Litre pinto. Looking for advice regarding the vacuum i.e. can you blank off the vacuum pipe from the distributer...is it needed? Thank you
-
- 4 replies
- 1.5k views
-
-
Cutting a long story short. I had the cylinder head off to replace stem seals and lap. All back together and the car ran like a dream. No more smoke and smooth running. Did about 20 miles. Filled up with fuel and she began to run rough. Good on throttle with occational mis but no idle at all and lots of popping on the overrun. Suspected fuel issue. Cleaned jets,checked float etc. Still no idle. Although timing had been checked I decided to give the dizzy a little turn while it was running and I was holding the throttle open. Huge backfire through the carb ( a reminder to everybody to always keep your face away from the top of an open carb!!) Hey presto..prob…
-
- 7 replies
- 2.2k views
- 1 follower
-
-
Dose the linking bar need to be there between the engine mounts?
-
-
- 5 replies
- 1.7k views
- 1 follower
-
-
Have today checked the electrics and the light etc all work. Turned over the engine successfully using start button have not connected the ECU My questions are I havent heard the low and high pressure fuel pumps come on yet ,are they controlled by the Ecu ? Secondly do i have to set up the ecu using the laptop and the disc provided? Am not confident enough to put fuel in tank ,connect the ecu and go for it. Thanks in advance Chris D
-
- 1 reply
- 934 views
-
-
So I started doing a compression test on my 2l pinto. I noticed that cylinder 2 was slightly down on compression and on advice dropped a little oil in and sure enough the pressure reading increased. It’s not starting comfortably now although just about got there in the end. Dumb question, would that be because of the oil in the cylinder? Is that a good or bad thing to do?
-
- 19 replies
- 5.5k views
-
-
Had two good weather days on the bodywork. Today was pants as my Irish wife says “ that’s wet rain that is”. so a good day on the engine started at 06:00 finished at 17:30. Very happy boy. I have a facet pump dose anyone know if I need a fuel regulator for twin Weber dcoe 40’s. And if so what regulator to buy.
-
- 4 replies
- 1.4k views
- 1 follower
-
-
Looking for a good used fast road cam for a pinto circa 1984 two litre. Not sure which one to go for, The engine is unmodified at present but in future, hopefully put two 40s on it. ALSO, does anyone have a manual choke kit kicking around.
-
- 1 reply
- 931 views
-
-
I got my block back from the machine shop, I purchased oversized pistons 91.209mm. The machine shop supplied me with new piston rings which were 90.80mm + 1mm This were too big? Looking online I can see 90.80mm + 0.50mm = 91.3mm. My pistons are 91.209mm which means the +0.5mm rings will be 0.091mm too big. Is this small amount of tolerance acceptable?
-
-
- 7 replies
- 2.5k views
- 1 follower
-
-
Getting the ported head ready. Waiting on the machine shop to get the block back and start the rebuild.
-
- 0 replies
- 770 views
- 1 follower
-
-
Just setting up the rappers on my refurbished ported head and set exhaust valve to .25mm and inlet to .20mm. When the valves are fully open they are further out than the cylinder head. is this ok?
-
- 3 replies
- 1.2k views
- 1 follower
-
-
Dose anyone know which way round the camshaft seal should be installed ?
-
- 2 replies
- 1.1k views
- 1 follower
-
-
HI everybody. I am a new member and have just bought an 2000cc pinto S7 with my son and we are having some shakedown issuesadd with overheating. The previous owner was a builder of BRM racecars and seems to have done a great job with the exception of cooling issue. Basically we heat up to 90norm in minutes and starts to overheat after more than a few mins in traffic. Even when running at 50mph on a cool day (14c ambient) - it never really shed the head and sits between 100-110c Shortly before selling, previous owner fitted a new twin core aluminium radiator, and a small electric fan on an isolated switch, which we always leave turned on. Hypothesis is…
-
- 31 replies
- 6.9k views
-
-
Any recommendations for Twin Webber dcoe 40 linkage kit?
-
- 1 reply
- 812 views
- 1 follower
-
-
hi can anyone with a std 2L pinto tell what there engine temp gauge reads when say at 70mph cruising ?
-
- 8 replies
- 1.6k views
-
-
I need to convert my water cooled choke on my 1984 2ltr pinto to a manual one. does anyone have an old kit kicking around their garage I could buy?
-
- 3 replies
- 1.5k views
-
-
Hi What is the normal pressure rating for a expansion tank cap (mine is currently 20psi). Reason for asking is took my Super Spec on a local track day and it was fine on the 80 mile drive down and managed 2 X 15 minute track sessions but on the 3rd session it decided to over heat and push all the coolant into a collection bottle I have running off the header tank. Filled it back up and it seemed ok on idle (got up to temp and a little after fan kicked in) but decided to call it a day as far as track was concerned, but about 6 or 7 miles of driving back temp shot up again (120 degrees) then dropped a little only for it to shoot back up so had to get the "rid…
-
- 7 replies
- 2.4k views
-
-
My block is in the machine shop and will be fitted with oversized pistons to 91.290. I have a ported head with a fast road cam and twin 40 Webber's. Can anyone recommend fuel pump and regulator. Regards Tony
-
- 0 replies
- 834 views
- 1 follower
-
-
Hi all, I started to change the bottom end front oil seals on my pinto, set the crank to TDC but the cam wheel is a vernier type which doesn,t have a timing mark, checked the rotor arm and its pointing to No1. 2 questions would you just mark the cam pulley and replace it as marked. It may have this pulley fitted because it poss has a uprated cam, does it need this pulley or could I fit a standard one
-
- 3 replies
- 1.4k views
-
-
Not a bad days work. Found old core plug in the engine block and broken water pump. Then found end of the dipstick in the sump must have broken off as sump was lowered then found scoring in the bore...... this engine was meant to have been rebuilt 5000 miles ago by ford mechanic..... you just don’t know what you are buying! Most of all love my car, Bloody love this club and it’s members and to do this with my 11 year old son.... priceless
-
- 1 reply
- 1.1k views
- 1 follower
-
-
Hi, have had a tuner set up the car today. It has a twin 38 non progressive carb from v6 on, its running very lean and he cannot get it set nicely,overrunning, he has advised I need the 32/36 to suit my fast cam, can anyone confirm what they have on?
-
- 5 replies
- 2k views
-
-
Hi all. Just picked up my s3 at the weekend and the paperwork for the twin 45s being setup says the timing is advanced to 16 degrees and it needs to be 10. Does anyone have any knowledge on whether the mbe967iD ecu will control the advance in the timing or if its more likely to be the vernier cam pulleys which are set up wrong. Thanks
-
- 4 replies
- 1.3k views
-
-
My car seems to have developed a fear of starting if its been left for a few days Im sure it began doing this only a few months ago , the engine turns but doesn't fire in to life till 4th or 5th attempt. It used to be fine when I 1st got it and even when it spent months having dash rebuilt it fired up 1st time. Its a 2L rover T series engine and I have changed coil, plugs, leads, distributor cap and arm. Once running it doesn't miss a beat and I can stop and start it with no issues. I would have thought a fuel pump issue would be there all the time and be worse under acceleration, could the fuel be evaporating in the lines (injection so no carbs to worry about) but …
-
- 5 replies
- 1.4k views
-
-
hi guys, new to this so bear with me, bought a s7 running 2lt pinto with modified cosworth rod and pistons. problem is a piston as blown and i cant get a replacement i need a 90.8 +1.55mm with a circlip gudgeon pin, tried burton power ect and i am having no luck. any ideas would help please
-
Hello all. Just joined, wanted to ask for advice. Bought my super 7 10 weeks ago. Im sure its still a great buy. Its had quite a few upgrades but i wasnt happy with oil splatter from the crankcase breather outlet or the catch can outlet. The car came with a breather outlet on oil filler cap which was connected to a 2nd breather higher up the block then runing into a catch can and out to air. I wasnt happy with the oil spitting out the crankcase breather or the outlet from catch can. Pretty messy and lots of vapour coming out from under the bonnet. I tied in a 2nd can and lead crankcase breather to that then up to inlet manifold. Im prob catching at least 150ml oil every 1…
-
-
- 23 replies
- 11.1k views
- 1 follower
-
-
My Robin Hood super sport with its original SD1 radiator mounted at an angle needs replacing. It runs a Rover 2.0 turbo. Any suggestions for a replacement bearing in mind the top mounted intercooler? thanks I’m advance
-
- 2 replies
- 1.3k views
-