Zero Wiper holes

[Thrashed]

Hi all.  Hope everyone is safe and well.

I need some help from Zero owners. I have the zero standard chassis, so if anyone can help, that would be great, to make sure I get the correct parts and mount them roughly in the right area. 

I have finally given in and am moving from the aero screen to a full windscreen.

I am measuring up for wipers and need some measurements as follows:

1 - Distance from screen to wiper spindle hole (gap between screen and wiper spindles)

2 - Wiper spindle hole centre to car centre line

3 - Wiper arm length

4 - Wiper blade length

Many Thanks

Steve

[brumster]

I'll do it tomorrow for you

[knights_templar]

Hi

Does the scuttle have the pre cut holes for the screen brackets?

If So

https://www.dropbox.com/s/wctjey9hf0d7guj/2013-02-06 15.44.52.jpg?dl=0

Get kit

https://www.dropbox.com/s/30ar21imqpzqxyc/EXTWPS2_IMG_2681.jpg?dl=0

Fit kit

https://www.dropbox.com/s/45gsnuy1ev66d9e/IMG_5849.JPG?dl=0

Sorry, still looking for measurement to cut tube, think they are in the manual somewhere

Mod wiper arms

https://www.dropbox.com/s/dl8pm4g7rv757q7/wiper arm build.docx?dl=0

Shout if you need anything else

Regards

[brumster]

Here you go! CL reference is the tab on the back of the dashboard/scuttle. All measurements are mm.

One thing I would say is remember there's a certain amount of adjustment in the wiper blade (for me at least) they can be varied in length and bent (and they needed it!)

Edited April 17, 2020 by brumster

[Thrashed]

8 hours ago, knights_templar said:

Hi

Does the scuttle have the pre cut holes for the screen brackets?

If So

https://www.dropbox.com/s/wctjey9hf0d7guj/2013-02-06 15.44.52.jpg?dl=0

Get kit

https://www.dropbox.com/s/30ar21imqpzqxyc/EXTWPS2_IMG_2681.jpg?dl=0

Fit kit

https://www.dropbox.com/s/45gsnuy1ev66d9e/IMG_5849.JPG?dl=0

Sorry, still looking for measurement to cut tube, think they are in the manual somewhere

Mod wiper arms

https://www.dropbox.com/s/dl8pm4g7rv757q7/wiper arm build.docx?dl=0

Shout if you need anything else

Regards

Thanks KT, already been given the 1st picture with the measurements.  Good and useful info.  Must admit I have been looking at the Car Builder kit which looks the same and has options of sweep available, plus is about £50 cheaper!

Thanks again

[knights_templar]

I should claim copy right infringement.

 

[Thrashed]

15 hours ago, brumster said:

Here you go! CL reference is the tab on the back of the dashboard/scuttle. All measurements are mm.

One thing I would say is remember there's a certain amount of adjustment in the wiper blade (for me at least) they can be varied in length and bent (and they needed it!)

Thanks Dan. Confirms a lot of the measurements.  Just out of curiousity, why park on the passenger side?  Most I have seen park on the driver's side?  

Cheers

Steve

[brumster]

This layout gives way better clearing of screen for the driver, it gets up nicely on the right-hand edge (as the driver sees). I spent a long time carefully trialling and positioning the blades to work out where the holes would go (my car wasn't pre-drilled, thankfully). I was so thankful of these at the Wales weekend the other year - they really made the whole weekend so more "pleasure" than "pain" :). Standard Defender wiper motor in terms of sweep angle/gear.

[Thrashed]

44 minutes ago, brumster said:

This layout gives way better clearing of screen for the driver, it gets up nicely on the right-hand edge (as the driver sees). I spent a long time carefully trialling and positioning the blades to work out where the holes would go (my car wasn't pre-drilled, thankfully). I was so thankful of these at the Wales weekend the other year - they really made the whole weekend so more "pleasure" than "pain" :). Standard Defender wiper motor in terms of sweep angle/gear.

Cheers Dan. Gives me something to think about!    Will have a play around this weekend. Always good to get another perspective. 

Thanks

[nelmo]

That's quite weird - my holes are symmetrical from that CL (2015 GT chassis, holes pre-drilled) so I had a choice which way to park them. I tried them on passenger side but seemed a bit better on drivers side - not much in it. 

Edited April 18, 2020 by nelmo

[MarkBzero]

Mine park on drivers side. I was told by GBS they are centralised so the same panel fits for left hand drive cars.

[Thrashed]

Thanks all.  I am luck enough that i dont have an holes pre drilled.  This means i get a choice.  Having done some mock up i think i will be copying Dan and go with the passenger side park.

It seems to sweep a bigger area of the drivers side and higher on the screen too.  Having a blank canvass means i can fit the screen and then tweek the wipers to fit.

What could possibly go wrong!!  

[nelmo]

Cool model

[richyb66]

One can only hope the actual thing turns out as well.