Jump to content

Regrettably My Robin Hood Exmo Is Now For Sale


KenHardy
 Share

Recommended Posts

Regrettably, time has come to part with my pride and joy. Not because I want to but because age has crept up behind me and I now no longer have the ability to get in and out. So here we go, Robin Hood Exmo Kit Car, Based on Ford Sierra with a 2.0 litre Ford Pinto engine mated to a 5 Speed manual transmission. It has covered 16643 miles since build. Purpose made plastic wind deflectors, Tonneau cover for every day use and full wet weather gear including side screens (not shown in photos) for when the British weather catches you out. Repacked exhaust to reduce the mind numbing exhaust noise on long journeys making it a pleasure to drive, Lockable storage area with built in tool box in lid. MOT expires at the end of July 2013. Tax expires at the end of February 2013. This car was built and registered in 1997 and has only missed 1 trip to the Le Mans 24 hr race since registration. Please email me for more photo's. Vehicle located in Swindon, Wiltshire. Viewing recommended. Price is £4,500. Call Ken on 01793535859 or 07875637284.

post-10592-0-57036300-1344881493_thumb.jpg

post-10592-0-87928200-1344881583_thumb.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Amateur
      Hi folks.
      I decided that my Exmo needs doors for when it's cold or wet. And since I could not find any doors that fit my expectations, I decided to build them myself. I created a simple aluminum frame and put 2mm plexi glas on it instead of a soft cover. And while the ready made doors slope forward at the rear end,  my doors slope backwards from the lower start of the rear fender, ending just a few inches short of the top edge of the roll bar where my doors get fastened. Maybe a little heavier overall (2.3 kg/door), but they are sturdy enough to not shake when driving and they keep the icy wind out when I drive my seven on sunny days in winter at near freezing temeratures. And in case it rains and I have to put the roof on (that I am also about to fit to the car), the opening is large enough so I still manage to fold into the car (I am not 20 anymore 😉 ). But the downside is, that the doors do not fit into that tiny boot of the seven. If I put the doors on to keep wind and slashy water out, I cannot take them off during a trip.
      So I have to come up with another, more flexible solution for those summer days when I want to enjoy the wind around my head while it's dry but still be prepared in case it rains.
      Now I wonder if those ready-made doors would fit into the back of the seven. Can anyone tell me? That would be great.
      You'd probably be interested on how these doors look. But writing this post I reallized that I never made pictures of them and my seven just went away to get a new paint job. So all I can provide today is a picture to the right driver side door leaning against my garage wall. I promise to add better pics of the doors attached to my car once the car is back and put together again.
       

    • By Sparepart
      I am rebuilding my Exmo, in a few weeks time I hope to reach the front end. When I put it together the first time I made sure that the wheels were squared up, in line, body in middle etc. It took a long time measuring before I bolted it all up. There were just too many measurement going on for me to consider caster, I just let things settle where the bushes seemed to take them. The result was even tyre wear, no wandering, no crabbing, BUT no self centering. I have skimmed through the 77 other topics in this forum that mention caster. I did not notice anyone making adjustments to caster on an Exmo. As I see it, I can't change the fore and aft position of the top of the strut because its trapped in the outrigger. The only way is to move the bottom by sliding the antiroll bar forward or backward. In principle a simple thing (I think) just move the two U clamps. I wonder if anyone else has tried this?. Is it worth making the mods so that it is easily adjustable, like mounting the u clamps on beefy brackets with a screw adjustment that can then be clamped firmly?. I am not confident that I can measure the caster accurately enough ? to say add x degrees of caster, so if its easily adjustable I can set it via a suck and see approach? If I over do anything then it could get dangerous and behave like a supermarket trolly.   Any insights would be gratefully recieved.
    • By Burney
      Hi
      I'm wiring a new CBS prewired 'loom/fusebox' into my exmo after upgrading and adding a number of electrical fittings and accessories that were either missing or broken on the car (lights/horns/reverse/fog etc).
      It has been relatively straight forward tracing the circuits to the accessories and switches using a continuity tester and diagrams of the ford stalk switches attached.
      I have some general queries on the major engine component connections though and ask for comments and advice.
      UPPER 5 - shows wire to + side of alternator. The existing connection comes off a relay should I leave this?
      UPPER 6 shows a connection to the starter. This is the live feed to the fuse board, made live only when igniton turned?
      UPPER 10 shows a connection to the accessory part of the ignition switch, whats this for?
      LOWER 2 shows 2 connections one to a fuel pump (I dont think the pinto has an electric fuel pump?) and one to the positive side of the coil. There are only 2 wires I can see coming back to the existing loom from the coil and both go onto the rev counter (which doesnt work yet). Other cables from the + side of coil go into some sort of silver plate?
      I have an existing battery isolator switch wired up which I like. Where is the best place for this in the new setup?
      Thanks in advance for your thoughts
      Kris
       
       


    • By Burney
      Hi all
      My original glass bowl lamps are very attractive but very dull is there a replacement LED lamp unit I can fit?
      The sidelight is non existant in the origibal lamp but the bulb and wiring is taped out the way so would be good to get a combo unit
       
      Kris
    • By Burney
      Hi folks
       
      I'm a new RH Exmo owner. Great fun had at back end of summer although as the darker nights approached I noticed my rear lights are not working but the headlights are.
      Indicators are off too
      Are these all on the same citcuit/fuse?
      Hoping to play with this problem over my xmas hols
      There are a number of other electrical issues for me to work through but lights are a badic requirement for me to enjpy safe road fun
      Kris
×
×
  • Create New...