Jump to content

Recommended Posts

Posted (edited)

Some bits for sale...

 

Fuel level sender, 6-hole flange, 270ohm, as sold by Car Builder Solutions. Hardly used. Float arm already configured for GBS 27litre tank. £24 new, sell for £15 including postage...

z_Lk6lC6nX3ee2H6MPTJ8j_l0AJhiWlFRQl1422u

 

190mm (7.25") clutch cover, typically Ford Crossflow (fits Rover K-Series though, fwiw!), standard, has done <500 miles. £35 plus postage.

 

4yNTVJIAp2DFrKaFaa_Vqee9sUgufhRkJuFO5p2CpeE6Nnf9hI2X__d4aYOJyqh0K-7Zsuzh_-aATm_V

 

Ford Duratec Caterham lightweight flywheel and 215mm (8.5") AP racing clutch setup. 1"/23T spline. Shows signs of use as it came from a race car; but just heat spotting, the flywheel surface maybe you'd skim, depending on what you was using it for you might decide to just stick it in and use it to be honest, there's no significant scoring or wear really, considering. Pressure plate in a similar vein. Friction plate was replaced and is practically brand new - CP5352-14 part number, specs are 7.11mm brand new thickness and this measures 7.07 as you can see, so the friction plate is a bargain for someone (£150 new).

 

Say £100 for the flywheel, £100 for the friction plate, £50 for the cover.

 

GilbwHrPqRA5ikzeRGRBZ1128nf5rUa1TZwRzzR7

7wjacrXsQiR2YhrJuG_nboxZyZ-wlwGdMy7gO1sv

Ht2tNaxbaaieYYeyl0SoSzBM11DH559VuX4TcaGs

iroQ-2u5yrlhnZb6RStk9vkzTpfWJbidqJXRIycm

b5nmr4yR5_y6OJGAeSEU3hhD8nY8X9Q0_rZSNK-z

RIkIJ8oGc3ZdG0p1quaEiBBs-3GoWd0VBXs74J05

Edited by brumster
Posted

Im interested in clutch cover and friction plate

Have already got a lightweight flywheel that is 270mm across not including teeth, 140mm inner recess. Clutch cover bolt pattern pcd is 250mm

If your clutch has same bolt pattern I am definatelly interested

Posted

According to our bathroom scales, half a stone (which equates to 3.17Kg)....

about the same as what i have already

Posted

Im interested in clutch cover and friction plate

Have already got a lightweight flywheel that is 270mm across not including teeth, 140mm inner recess. Clutch cover bolt pattern pcd is 250mm

If your clutch has same bolt pattern I am definatelly interested

 

Yep, this is pretty much bob on those dimensions (if I'm being picky the recess is about 142mm and the PCD is about 251mm :D )

Posted

Well Im up for it

After finding the Fiesta ST clutch does not fit the flywheel

Nor does the Pinto AP clutch set

Or the Mondeo clutch kit I just bought

If we can sort payment, I think bank transfer would be good and delivery/postage we can settle the deal

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...