Jump to content

Driving Again

MarkBzero

By MarkBzero,
in Chit chat

 Share

Recommended Posts

MarkBzero Wheely good builder!

MarkBzero

Posted
Posted

At long last after 8 weeks off work recovering from an operation I am allowed to drive again. So whilst sitting at home doing nothing and bored stupid with day time TV I decided to treat myself to a new exhaust shield to stop me worrying about my son burning himself on the exhaust can.

 

post-4145-0-55694500-1457863487_thumb.jpg

 

Then on the test drive I tried the new accident dash-cam, only a cheap version from Aldi, but I was surprised with the quality and think it is good enough considering yesterday day was cloudy and overcast. A lot of back ground noise but I suspect even an expensive cam will suffer with wind noise.

 

 

Link to comment
Share on other sites
mark little Wheely good builder!

mark little

Posted
Posted

That's pretty good quality, I'm a bit annoyed because I was going to get the same camera but they didn't get them in the aldi branches up here or it might be I went to lidl, can't remember now.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
 Share
Go to topic listing

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • MarkBzero
      Suspension bushes
      By MarkBzero
      Hi technical experts,
      I need new suspension bushes for Ford based Zero, I have used GBS ones but they have appear to failed after 1200 miles. 
      Does anyone know of another supplier who sells them? Maybe better material. 
    • Pthomas
      Bone Fide Gbs Zero?
      By Pthomas
      Hi All,
       
      Uncertain and inexperienced new member asking for a quick bit of advice please!
       
      I have agreed to purchase this secondhand GBS Zero - please see expired eBay listing:
      https://www.ebay.co.uk/itm/122578482611
       
      I've just checked on the DVLA website, however, as its registered as a Robin Hood. Questions:
      - Is this is genuine GBS Zero? Is there a way of checking or can you tell from the photos?
      - Assuming it is, does the slightly incorrect registration cause any issue/ concern?
      - Any other thoughts welcome!
       
      Due to exchange on Saturday so apologies to ask for a quick response...
      Many thanks all.
       
      Pete
    • Jim Gould
      ... Just A Bit Of Good, Clean 7 Fun
      By Jim Gould
      Here’s a brief Public Service Video (kindly provided by The Simpson Driving Academy) that you may find of interest.
      https://www.youtube.com/watch?v=3ioxStlhOww

      SevenSpot:
      https://www.facebook.com/groups/1604902176413856/?fref=ts
    • bennyben
      Zero Suspension Build Questions
      By bennyben
      Hello All
       
      I am piecing together my Zero and have a few suspension questions for the old hands out there:
       
      1. The front suspension bottom ball joints are held in place with 3 bolts each side. I have noticed that the GBS-supplied nuts have been squashed a bit on one side to make them off-round. I've never seen these before, so here's my question - do you apply a locking compound to them or just tighten to the specified torque and leave them?
       
      2. Out of interest, does anyone recommend applying locking compound to nyloc locknuts?
       
      3. Do you use washers on the nut / bolt for the bottom ball joints? There aren't any supplied in the fitting kit.
       
      Many thanks for your help
       
      BB
    • MarkBzero
      Fitting Zero Hood And Doors
      By MarkBzero
      Advice needed from anyone who has fitted hood and doors, where do you start? Where do you fit the support brackets for the frame? Do you use rivets or screws in screen frame or rear panels?
      I have the standard narrowbody zero kit.
       
      Thanks
      Mark
×
×
  • Create New...