blue

Hi what ride heights are you guys running eg. 6 inch bottom of chassis to floor on front and 9 rear etc At the moment my lower front arms are paralleled ??

Will you be making any more ??

Hi if you stick with one m/c use standard sierra one if bias bar use 0625 front and 07 rear and 07 for hyd clutch

No self centering is very poor !! Can I measure caster by simply measuring hub angle like I would with a king pin EG measure this angle /

Will do and thanks blue

Hi no not just motorways it just don't inspire confidence on any road Just so I'm straight is that 1.5deg camber front and rear or just front ????

Also what caster angle would you say ?? At moment tie bars are set where they would be if roll bar was still fitted !

Yoko paradas. 6 month ago Would you suggest a little more rear camber ??

Hi thanks for all the replys ... And now for the replys !! 1. I have cycle wings fitted 2. I have tie bars 3 Tyres are 18/19 psi (cold) 4. Front springs are 80 pound 5. Rear springs are 120( maybe 140). Would have to check !! 6. Rear camber is set at 0 deg. 7. Rear toe is set at 0 8 Front toe is 1.5 deg toe in 9. Front camber is set 0.5 deg negative Again thanks for all answers so far. Great club !!!!!

Hi I have a s7 mono and at motorway speeds 70+ it's just damn scary. It's like the car wants to float And it will drift !!! On a B road blast it can hold its own but on a high speed run well !!!! Went out in it last night just to give it a run out and ended coming home in the wind and rain and found I was on the motorway sh*ting myself doing 35/40 mph with the car feeling like its aqua planning and drifting I have been all over the car and nothing is loose or broken ' Suspension settings are shimmed rear hubs so camber and toe corrected , front 0.5 deg camber and 1.5 degree toe.

If your facet pumps ticks there is a small amount of air trapped in the pump

Any chance of some pics ??

See I took mine off but now after reading this I'm not sure if I should put it back on ?? After reading the burton article it seems that it has an PCV valve fitted which if I fit a tube to it and aim it at the floor will remain closed anyway and do nothing as it won't have the engines vac behind it to pull it open ?? Or am I missing something ??

Don't use the ford sump you'll get oil starvation !! The engine won't last one spirited drive ! The ford sump is designed for horizontal fitting and is baffled for such. You can get away with using the cvh sump but if your going to the trouble of fitting a zetec budget for a proper sump !

Hi is there a list anywhere of what shops we as members get discounts at ?? Sorry if this has been asked before .

Hi any starter motor /alt recon shop sells ribbed pulleys to fit ACR type alternators There like £3 Just make sure your alt has 17mm shaft not 15mm as you'll need to make up a sleeve to convert !!

I have set all the pedals at straight up (12 o clock) and the travel on clutch is perfect aas it stops on the pedal box and throttle travel is spot on full throttle on the ford butterfly I also fitted a bias adjuster on the dash to help set the bias All in all these boxes are easy to fit .

I have one of these pedal boxes I used the GBS left hand drive clutch cable And the left hand drive throttle cable , drilled a small hole through pedal put solder less nipple on end job done All connected up to my 2.0 zetec. My only complaint is pedal box is quite flimsy . It could do with being made about two mill thicker material

Glad I could help. Ps did the wife give you the kit car widow speech ha ha ha

I have one you can have! It's been sitting in my lock up for about 3 yrs. I bought it as a spare but never used it. But I'm in London !!

Hi don't use rubber hose along length of car cos it sweats and you'll have that petrol smell all the time like an old ford cortina !!!

Hi need a bit more information pls Eg fully car loom,omen loom ,webcon, mega jolt etc

I have a complete set of brand new (fitted for 3/4months) twin 45weber carbs for 2.0 black top These were personally jetted by Alan Collins on webers own rolling road (20+yrs webcons senior technician ) They are complete with manifold ,sausage filter,fuel pump , filter regulator , linkage ect You will need to buy nothing else ! The engine was doing 173bhp and on sensible driving around 25/28 mpg I then had a major change and got Alan to do me a bespoke full management system inc fuel inj So I no longer need these Open to sensible offers but would like around £700

Yep big welcome to the club. What ever the question someone on here will have the answer And remember everyone on this site has asked a silly question at some point !