Wanted

In the interest of this board and the Club members, PLEASE read the above rules and keep any posts in here "ON TOPIC", e.g. not casual converstaion/waffle/spam.

Does anyone have robin hood nose badge for 1980 dolomite sprint based car for sale

Does anyone have for sale or know where I can get a frame for the soft top on my super spec? Mark.

Don't suppose anyone has the standard water pump, alternator and bottom crank pulley that drives the water pump belt,for sale do they? My car came with these horrible blue toothed pulleys that shreds belts,

Hi. I need a cambelt cover for a 2l pinto. Can anyone help pls ? Located reading area. Cheers John.

Donar Car, Ford Sierra, SOHC, T9 gearbox, Ind rear live axle, LSD, looking if I can take out the anti-sway bar and fit the tie- rod kit.

I am trying to find someone who has camber wedges for sale to suit a 2b . Thanks in advance

I have a friend looking for his first kit car, something that needs no real work ready to drive Mazda or Zetec engines preferred good tidy condition budget max £10k pm me if you know of anything at all.

Hi. I have a worn plastic bush in my steering rack which is from a 2985 Sierra. It matches the pictures in the Haynes manual. All it needs to get at it is the ford tool 13-009 to remove it to be able to withdraw the rack. I'm either trying to source that tool or replace the rack which is proving quite hard. Does anyone have a rack they could sell me? Or the tool they would trust me to return on completion? Many thanks

Hi Has anyone by any chance got a spare sandwich plate that fits between a type 9 gearbox and a 2.0L pinto, wanted for project, pref cheap Thanks in advance Regards Harry

Help, Has anyone changed their DFTH carb & ESC 2 Engine control module and still has the connectors ideally with local section of the loom or wires still attached ? (Item 20 & 59 of page 437 of the Haynes Ford Sierra owm) It looks like I'm after what appears to be hens teeth having scoured the web over the last couple of years with no success Alternatively a) Has anyone any idea if there is a supplier / maker of especially the ESC 25pin Motorcraft connector ? b) Anyone knocking up the 25port body & cover on a 3D printer ? c) Has anyone overcome this connection problem and ditched the ESC 2 ideally with a basic wiring diagram run…

Hi all, Bit of a long shot, I am looking for 1 of the wheels as seen in photo to go as my spare, if anyone has one for sale I’d love to try and purchase it. Fox 2B, 14 inch 4x108

As title. Looking for a Duratec lowered sump, ideally a second hand one, I know where I can get a new one.

Robin Hood Exmo C122GRH I built this car in 1986 and regretfully sold it some years later. I was an active member of RHOCAR during this period as area sec for Hampshire. The car was last taxed in 1997 and mot’ till 1998. I would dearly love to trace the current status of the car in the hope it is under a tarpaulin in someone’s garage with a view to re-acquiring it. I have now rejoined the club hoping the clubs records or current membership may point me towards the last recorded keeper. Any information would be greatly appreciated. Steve Potts

As title. I'm looking for a set of used good or new cams, Kent model number FZ2002 to suit a Zetec silver top, and/or a set of vernier pulleys. Thanks, Andy

I'm on the lookout for a stainless fuel tank for a 2B, the original RH one, ideally the bigger capacity one. It's not for me, I'm after one for a mate's car. Any leads appreciated.

I'm looking for a 2L Zetec Silvertop engine if anyone is selling one? Preferably in Kent, but will travel for right engine. Thanks, Andy

Hi All, I am reaching out on a limb here as probably the only part that nobody has knocking around spare but I need to ask. Does anyone have or know where I can get a Bonnet for a MK3A even if it’s a fibreglass version Basically the powder coating company near me has allowed an apprentice to prep my bonnet and he has managed to bend it. I am devastated given I have spent hours sorting build issues from the original builder, fitting upgrades, bodywork fabrication etc the list goes on. I literally dropped the bonnet last week and got the call today. The gutting thing is that I was hoping to have it ready for Malvern…. Many thanks in advance P…

Hi guys. looking for Robin Hood 2b wet weather gear, or any ideas of a place that could make me a cover from the windscreen to the boot…… thanks Shaun

Hello everyone, I’m searching for a front damper for my Robin Hood ExMo. As far as I know, this is NOT a Ford P100 Cortina damper. Does some Exmo Owner changed their front suspension and got one left? Thank you very much! Best wishes

Hi, I'm looking for a pair of seats, preferably bucket seats, but any type considered. I'm in Essex but can travel. Thanks Phil

Looking for a decent exhaust shield burnt my leg one time too many !

Evening all has anyone got a sabelt seat belt in black with yellow labels as fitted as standard in the 3B one of mine is frayed on drivers side where it bolts to the tunnel cheers Darren

Hi looking for a branch manifold I have a 2.0 DOHC engine but believe the manifold fitting is the same .

Pretty unlikely but if anyone has a Ford top, front, n/s wishbone sitting around, I'd be happy to buy it off you.