blue

Hi not tech mine but my neighbour is selling a cracking 1.6 mx5. It's the mk2 with a small skirting kit and would make a really great donor for someone £1200

Hi can I ask what rev counter your using.

Hi. Any injection parts if that's the way your going eg fuel pump etc. you can also take the loom and ecu if you want to run it as ford intended but to be honest most people here started with a crate engine as there's not much else you can take from the car

S7 with 2.0 crate engine , type 9 quaife box ',GBS single plenum ,webber alpha on webcons development software 189bhp '38 to gallon

Hi have a look in car builder solutions book or web site. They have a pic of how to wire up your ind with only one light on dash with diodes that you can buy from them too !

Update !! We'll all front was stripped and the front suspension was all greased etc. from what I can see the builder put it together thinking that the nylon bushes were enough for the suspension to pivot on and assembled it with no grease ????? He also tightened the pivot bar so tight that even when the shock was removed the arm still needed a little encouragement to move up and down (I had to use a breaker bar to undo nut on pivot) so all redone and a 3mm plate temp put on till I find or am happy with a better way

Hi cb750 I take it looking at your pics that your front arms like mine are just held by the 2mm bent plate ???? Or is there something inside .

Hi yes my front looks exactly like yours but I don't have the angle bits on the top ?? I'm having a real hard time putting pics up it keeps saying file too big ??

hi thanks for your replys ive stripped the front down and found the bolt more or less stuck solid in the arm so at least ive found the problen im still amazed that the rfont arm is only sitting in a bent bit of 2mm stainless steel hi as regards to body roll on 80lb shocks its very minimal but thats only on back lane blasts have not taken it to limits on track yet also has anyone come across a very big (noisy) bang from the rear of the car if going over a pot hole !! ive read the posts on the bottom of the car (subframe ) hitting so have checked this ( put talc power over bolt heads etc ) and nothing was rubbed off after a drive ?? and it only happens fron near side never offside !!

Hi no his not running or needing an eddis. The omex has spark drivers built in Yes the crank sensor is plugged in and working but the car cranks with the same symptoms as if you turn an old style dizzy to far as in it will crank 2/3 turns then cough back with quite some force The car starts it runs for maybe a second or two if started with full throttle . It's deff got an air leak from the manifold cos it's so poorly machined the flat edge we checked it with actually rocked so as a temp measure we applied silicone to fill the gaps !! However the air leak is an easy fix what we can't seem to get round is the advance spark problem causing the engine to lock/stall on cranking !! So does anyone have a good known base map for a 2.0 zetec they can e mail flameredturbo so we know we have a starting point or a way or setting to retard the advance on an omex 600.

Thanks for your replys. Any pics would be good. Anyone else had this (see pic). I'm running 80lb front springs and tie bars. That happened the weekend. And me and the other half were only cruising as the weather really was not the best. Noticed it while parking it back in garage !!!!

Guys I know this has been spoken about lots of times and I have the usual chassis stress/cracking places on the front that seem so widely known about but what concerns me if it's cracking where I CAN see it where is it cracking where I CANT !!!! Has anyone come across any other places where the mono splits?? I can easily weld some plates /strengthen the chassis if I know where to look ?

Hi tracking is as near to dead straight as you can. 0 deg toe in /out

I'm east London but with a little notice I'd be up for a Kent drive out.

On suspension set-ups you never fit a rear roll bar if no front fitted !!

Glad to help. That's what this clubs here for !!!

Ok having read your other post I think it's time to go basics !! Do you have a standard carb and manifold to try. Also have you took the tops off the carbs and checked that the needle still has the circlip on it cos your post sounds like your running lean on one cylinder hence the AFR on your wide band has gone from 12s to 14. You say the slides are all moving but not that the needle is moving with it

Are you using the original 2.0 flywheel. Cos I'm using the starter from a 1.8 cvh and it works like a dream

Ok what engine you running. Pinto / zetec ?? Also what way are your hoses routed ??

Hi in people's option what's a better tyre the yoko parada or the AD08R

It's worth calling GBS as they still do lots of bits for the Robinhood I'd be very surprised if they don't already make one for it !!