Modificatons

Recommendations for the best semi slick tyres on 15 inch wheels

This mod for the Cortina based S7 rear axle to help stop axle wind up The RHE Fifth link set that this mod replaces 1) Remove fifth link set up if fitted ( if it is fitted you will need to plug the hole in the top of the diff casing) 2) You will need all 4 links from the rear axle of a mk1 Nissan Micra (two are for spares in case you mess the first two up) 3) Shorten two of the links by cutting out a 2 inch section of the tubing. Insert a bar between the two parts and push the two ends of the link together. Weld the section together when you have fitted all the brackets to the axle and the body/chassis and you have made sure of the length of…

For those with toughend screens wishing to replace them and in the leicester area. Pheonix Glass on knighton lane east will cot to your template for around £35

Hi Guys I've just purchased my first Robin hood (love it! 😍) and am looking for recommendations in the midlands. I have attached a couple of pics but they don't really show the issue very well. The car I Have has a lot of negative camber on the rear. What should this be set to? Also why do so many tyre places that do tracking say that they cannot adjust the camber? I have rang 3 garages so far but no luck. I live between Coventry and Leicester so ideally somewhere in that kind of area.

Hi all, anyone done a hydraulic clutch conversion on an MT75 in a zero? setup is MT75 mated to a Zetec with Pinto AP racing clutch and plate, cable clutch.

Hi there recently got to go through the ordeal of replacing the sump on my super spec The car is now running healthy again and has a better sump guard However it still scrapes on a lot of the roads around my area If I can raise the ride height even a cm I think it'll stop it but for the life of me I cannot figure out how to Attached is a pic of my coilovers I think I should be able to raise the ride height from here but I can't figure out how online it says there should be two rings bellow the spring I only have one there also is a hole for a grub screw but there is no screw in there Any suggestions on raising the ride height?

I want to obtain a Clubman 7 badge for the nose cone ,I am in Australia, can anybody direct to the right area please.

Hi everyone, I've bought a Tiger Supercat which has restored my enthusiasm for cars/driving again. As an old git, I need leading by the hand a bit and wondered if anyone knows of an LED headlight with the outer light ring that stays on when the ignition is on as a daylight running light? If they are available, does anyone know the manufacturer or where they can be bought please, I can't see any on ebay? Has anyone fitted them? I don't suppose it's a straight swap and imagine I'd need an auto electrician to sort, any thoughts or advice please would be greatly appreciated. Cheers Phil in Northumberland.

Hello community ! Sorry if I’m not following the rules — I didn’t see whether we were supposed to introduce ourselves or do something specific before posting on the forum (if that’s the case, I’ll do it right away). I’m currently considering buying an RH S7 (Cortina Mk4-based). I’d like to know if anyone has ever converted an RH to left-hand drive. If there’s any record of such a conversion, a guide, a kit, or a parts supplier to recommend, I’d really appreciate it. Also, could you give me an idea of the level of difficulty involved? Thanks!

Hi new member here although i was a member s few years ago in hoping i can get sone advice I recently bought myself another robin hood its fitted with a 2 litre zetec which has a supercharger fitted im having a lot of trouble tuning it its fitted with a microsquirt ecu is it a simple enoigh job to remove the supercharger and remap the microsquirt ? And use it as an efi ?

Hi new member here although i was a member s few years ago in hoping i can get sone advice I recently bought myself another robin hood its fitted with a 2 litre zetec which has a supercharger fitted im having a lot of trouble tuning it its fitted with a microsquirt ecu is it a simple enoigh job to remove the supercharger and remap the microsquirt ? And use it as an efi ?

anybody ever had any issues with oil leaking from the distributor on pinto engine.... Or around that area... Cannot quite make out if every time I drive the car it's the distribution or the fuel pump leaking oil. At least I know where the bloody leak is coming from on the gearbox sump....... Thanks for grounding it Nikki...! 😡 Oh well accidents will happen (shame it was the cars first time on the road this year).

Hi, Just wondering if anyone can help with this, I bought a superspec a month or so ago and received a brand new carbon fibre aero screen with it. I'm not going to use it and as it hasn't been drilled or fitted I though I could sell it. I am trying to find out what sort of price I could sell it for but I can't find it anywhere, second hand or brand new. The previous owner said he bought it for £600 but I just want to double check that as they seem to sell at a huge range or prices. It's in an ECF Composites box and they do do carbon fibre products but I can't find anything to do with cars on their website. If anyone has any advice or can fin…

Wondering if there’s anyway to upgrade rear suspension from the original shock obsobers and springs on the sierra arms and change to coilovers as ride is so soft and bottoms out with riding with passenger. or any advice on how to stiffen if swapping to coil overs can’t be done. cheers

Winter mods finished just waiting to get it set up on the rolling Road on the 5th Jan. Photo album of the conversion are here. https://www.amazon.co.uk/photos/share/M4DnC4AjGEeV3HeLzKVylCwJwRV6Mx5Wrm0HZ91KP97

Afternoon all, Newbie here, just curious to see what/if people have modified the gearstick length as mine seems like a lorry gear stick 😂 Is there a short shifter mod or is it a case of cutting it down? Cheers all Sam

Hi, bit of help please? Does anyone have a cooling system diagram for a 2.0 pinto engine? I am wanting to put an expansion tank in due to air locks. I have the tank & I know it needs to go high up as possible, I have a suitable location for it in mind. Also am I right in thinking that the heater pipes need to be low down as possible too? Any help appreciated! Cheers Phil

Just canvasing opinions on these, has any one got any experience of using one? Do they really live up to their promises? is there an alternative? Thanks Jez

Hello... Just need a starter motor at the minute but I will be putting a V tech in eventually. Any opinions? Has anyong got a link to a 2l starter motor? Thanks in advance ☺️

Has any body modified the handbrake on a super spec as I have finally got mine on the road but find the handbrake a pain to reac any info etc would be appreciated many thanks

I have done a huge amount with the car over the last year and am now going to look at the geometry in a bit more detail, currently I have camber wedges on the back and little else, I have looked at the Haynes build your own sports car by Chris Gibbs, some very old notes from Track Developments and came across Caterham CSR settings and this is the confusion I am trying to deal with. across the 3 the range for camber front is 0.25-1.5 degrees rear 0.66-2 degrees caster 5.5-6 degrees (CSR only) Toe front 0-0.5 rear 0.16-3 i am tempted to start with the Haynes settings but for now what are other peoples RH S3 settings for Caster, Camber & To…

Hi hopefully one of you experts will be able to help! What 52 mm round fuel guage will work with the sierra sender? Thanks in advance 😳

Hi all. I'm considering swapping my 1800 pinto for a zetec and was wondering of those that have done it what did you about the exhaust, did you have a complete new one made or modify the original?

Thinking of a colour change only the nosecone and arches ,and maybe the wheels ,it's currently dark blue with black wheels,I was thinking maybe a bright yellow or turquoise? Any suggestions? Or pictures of your car , thanks

A very good afternoon. I am in need of advice. The top hose on my Robin Hood Series III (2 litre pinto) has now reached the end!! It is very tired and split and will, I imagine, burst before too long. I have asked Burton Engineering about a replacement but they are unable to recognise from which original vehicle it may be from, by looking at the photographs I sent them. Before I possibly spend an eternity looking through online catalogues ...does anyone have any knowledge as to where I might best start looking for a suitable replacement? Thank you ... and would a silicon replacement be any advantage - providing I can track down the correct part?