ZeroKnowledge

should be useful if I overcook a corner & end up in tatty field

finally bought & fitted rear diffuser dont know if it improves airflow but gives my back end a much better look (ooh err) any thoughts??? Cheers Paul

its best & easier if you can use a laptop with serial connector. is it a new or used Megajolt? new ones have a safe base map preloaded that will run just about anything. if its used you can download it from autosportlabs website. there is also a section on the website with loads of maps on, should be a few for zetecs If you have Megajolt V4 you can have 2 maps loaded and switch between the 2 while driving. Cheers Paul

congrats & well done will you be adding a screen or enjoying the flies in ya teeth? Paul

Hi Phil PM sent

Congrats on first time pass good looking piece of kit, what engine etc have you used?? Paul

Hi Steve I have one of the Pela extractors if you want to borrow it, as said the only issue you might have is the tube wont go to bottom of sump. When I did my tintop I parked on a slope and it got every drop. Cheers Paul

Finally had a try with my camera on the zero I mounted it on the rollover bar upright hence all the wind noise. its lost abit of picture quality with the youtube upload dont think any oscars will be coming my way what do you think??? Cheers Paul

c u all later Paul

this what your looking for? Birmingham (AREA 08) VOSA - The Goods Vehicle Testing Station Granby Avenue, Garretts Green Industrial Estate Birmingham, B33 OSS Tel: 0121 783 6665 - Fax: 0121 603 4400 Email:Area08mail@vosa.gov.uk other vosa sites here http://www.transportsfriend.org/enforcement/offices.html Paul

Hi Craig I got on the road for £4000. but mine wasnt the typical build as I bought the zero part built for bargain £2700 and most parts were there to finish it. Cheers Paul

I have a DOHC in a zero, with bike carbs fitted had to do a few tweeks to engine to fit it, but the zero chassis was standard if you want to keep EFI, Redspec on here may have more info moved altenator to below water pump even with a shortened sump I lifted the engine so sump is level with floor, so had to put bonnet bulge on as engine sticks through bonnet.(see pic) some people have changed the flywheel as its v v heavy but i didnt bother hope this helps cheers Paul

have a look on the disc,there should be a file with the info on got my cam last week, still havent had a chance to try it in the zero cheers Paul

gonna have to miss this one Cheers Paul

ordered one with 8gb card last week, arrived this morning easy to use once you know what the lights mean the only downside is the car charger as its abit flimsy, but some tape around the joints should sort it. will try it in car tomorrow if weathers ok cheers Paul

got the coolman on my zero Paul

have you tried autosportlabs website? theres a section devoted to maps

can you get another hoodie to have a look. a fresh pair of eyes can pick things up. I felt I had missed something obvious and was still in garage at 1am night before test checking things over. If your driving to test ensure insurance is sorted, if trailering have a trial run getting on & off trailer My tester was ok, even made me a cuppa & was happy to answer any questions/give advice Good Luck Paul

made the most of a dry sunny day today & had a 2 hour blast. The back roads around Northumberland are great but they were still abit greasy. been back in the house 3 hours & still grinning. roll on the summer!!!!!!

ten years ago I was done for doin 108mph on a bike on dual carraigeway, I contacted RAC legal dept for advice & they sent me a generic "grovelling" letter. I took the letter to court adding that I needed transport for working shifts. considered myself very lucky to get 6 points & £280 fine when everyone else in court that day was banned. never been caught since Paul

that sounds like abit of a rant!!!!!!!! I was well back- thats how I could move out of way.

had a bit of a brown trouser moment this mornin on A1 following an artic when a slab of ice & snow about 6 foot square fell from the back of the roof, luckily seen it coming and got into outside lane, could have been v nasty if I had been a bit closer. would the artic driver get charged if it had caused an accident?? Paul

well done Nick thats great Paul

Hi Daz I have pm you the info I got with my Megajolt V4. it may be of help. The sheilding for VR & pip/saw is ONLY connected to pin 7 on edis and pin 9 on edis is earthed cheers Paul

thats another step closer to iva, any dates in mind yet??