Jump to content

jacko

RHOCaR Member
  • Content Count

    22
  • Joined

  • Last visited

Community Reputation

2 Neutral

About jacko

  • Rank
    Builder
  • Birthday 08/29/1948

Profile Information

  • Gender
    Male
  • Location
    Bromley Kent

Previous Fields

  • Car type
    2B Plus 2ltr pinto 40s wishbones
  • Full name
    Alan Jackson

Recent Profile Visitors

6,536 profile views
  1. jacko

    Wheel Covers Made To Suit.

    HI Craig. Have seen your new wheel cover and looks good to me and would like one for my 2b + with red piping 7 logo not required how do i contact. Regards Alan.
  2. jacko

    Robin Hood 2B Parts For Sale

    Neil. Message sent Jacko.
  3. jacko

    Robin Hood 2B Parts For Sale

    HI. Neil if still going put me down for wind deflectors. Regards JACKO.
  4. jacko

    2B Nose Cone Question

    My nose cone is a untouched original and measures 30mm on the top going down to 25mm at sides. Jacko
  5. Thanks lads i'll give some heat a go i've no nails left and finger tips are red.
  6. HI. Any one have a good method or short cut to removing the protective film from s. steel panels thats been on them for 12 years. Has gone brittle comes off in small flakes Without damaging the surface. Jacko.
  7. jacko

    2B Dash, Centre Console, Tunnel Top

    Good find have been looking for iva aproved dash and consol for a while now this fits the bill old steel one to be used as backing plate. Regards Alan. [JACKO]
  8. jacko

    Kent Area Lives!

    HI Bob. I can make that won,t be in my kit not finished yet Alan. (jacko)
  9. jacko

    Ford Sierra Fuel Sender

    Hi. cbs do a little magic box that can match your sender to another gauge cost 38.40 inc vat. I brought one to match a durite gauge not fitted as yet. Jacko.
  10. jacko

    Which Amp Gauge

    Hi all. Just about to buy and install an amp gauge which is best 30- 30+ or 60-60+ amps on gauge for my 2.0 pinto with alternator. Jacko.
  11. jacko

    Superspec Suspension

    Also i forgot to add a drainage hole is req,d to bottom of each well.
  12. jacko

    Superspec Suspension

    Hi. Alan Have just replaced front and back suspension on my 2b+ with gaz units from dampertec spoke with dave he advised rear coil overs for standard road use and average wieght driver 16inch open 300lb springs.I brought mounting shoes that sit in swinging arm wells from kit spares only a few pounds and holes were same as bush insert in damper.but dave does bush liners if you want make your own and reduce bolt dia size. Things i found when fitting mine 1. when i temp fitted damper with out spring attached in bottom of roll tube and let them hang natural in well the o/s one was off centre by 25mm due to frame build /welding .i overcome by making large round plate washer and welding in bttm wells for good seating. 2.Make sure you fit shoe in well to same angle as swinging pivot bolts A MUST also top mount bolt in roll over tube. 3.Don't over tighten bolts through coilovers and shoes just pinch up to allow movment swinging arm axis. 4.use bolts with long shanks so threads don't reck bush linings. 5.when fitting botom shoe in well fit bolts to coilover first really tight for space.Unless you make your own with extended ears. I have photos of complete build and set to mine if any help let me know i'll post them .
  13. jacko

    Iva Fog Light Circuit Testing

    Simon. Have just been looking at your posting on fog light switching magic box do you have one for sale . Regards Alan.
  14. jacko

    Seats

    Try burton power they have a solection of seats in there catalougue on line www.burtonpower.com or phone 0208 518 9199 for sales. 15mins drive past olimpic village on A11- A12 Alan.
  15. jacko

    Brake Line Fixings Dims

    Thanks for the info will crack on now.
×