Jump to content


DanE

Member Since 09 Jun 2007
Offline Last Active Yesterday, 07:22 PM
*****

#378709 Been On The Dyno Again (To Reduce Power)

Posted by DanE on 30 November 2017 - 09:53 AM

Nothing to do with mapping, it's to do with the twin throttle body set up and bypass valve, at cruising throttle the engine load is light keeping the bypass open meaning no boost. Slight change in load and plenum goes from vacuum to positive pressure closing the bypass and giving massive torque instantly. Meaning trying to cruise at 70mph is hard work. Thus the dual map and lo boost option. IE cold, damp, cruising, missis in the car mode.


#378704 Been On The Dyno Again (To Reduce Power)

Posted by DanE on 30 November 2017 - 08:13 AM

I have now got a car with dual identity, as you can see the boosted map ran 242bhp and 256ft lb of torque (same as before) which is great fun but hard to drive when trying to drive steady on a cruise up the motorway. so i have been trying to figure a way to hold the supercharger at bay which i have now designed and tested. so went to the the dyno again to get the 2nd map rewritten the car is is now truly awesome, i can have a normally aspirated easy to drive car with 130bhp then flick a switch on the move and have 242bhp making the car fast as feck ! 

 

Attached File  dyno results.jpg   74KB   0 downloads




#378281 10.2 Volt Battery

Posted by DanE on 08 November 2017 - 07:33 PM

Battery's knackered probably a dead cell should be around 12.6v


#378168 Rear Coilovers

Posted by DanE on 03 November 2017 - 01:22 PM

And will also most likely ground out on bumps


#378035 New Toy / Project

Posted by DanE on 29 October 2017 - 10:37 PM

It is a very nice car, looks great in the flesh and has a wicked exhaust note, look forward to runs out in the stylus


#377768 Retro Ford Zetec Water Rail

Posted by DanE on 18 October 2017 - 05:01 PM

Grumpy no, cantankerous maybe X


#377174 Mikuni R1 Carb Problems... Help!

Posted by DanE on 22 September 2017 - 06:17 AM

What sizes jets you need is guess work, I used fireblade carbs on my pinto with 1.40mm mains standard idle jets and blocked air correctors. If it was me I would find a standard carb set up for now. Bike carbs can be a diffecult thing to set up at the best of time, the only real way to get decent results is to find a rolling rd with a decent operator who understands bike carbs. When set up right they are perfectly good. Would I use them again ? Probably not. Good luck


#377129 Zetec And Electric Water Pump Still Overcooling

Posted by DanE on 20 September 2017 - 08:12 PM

I've been in talks with them after the generic email and having a discussion with demon tweeks who seem to have contacted them. I received a large email from DC with an apology and a large list of questions on my set up & specs. I answered everything which they then passed on to there chief engineer, they have concluded I need the ewp 80 and there other controller. I maybe miss reading there email but I think they are sending out new kit from Oz.if this then turns out to be the case then that is top customer service ! Either way they do now seem to be interested in solving the issues...


#377055 Mk1 Eunos/mk5 1.6 For Sale

Posted by DanE on 18 September 2017 - 03:09 PM

Sold
  • ozz likes this


#376830 Sunday Tinkering

Posted by DanE on 10 September 2017 - 05:19 PM

Working, my weekend starts tomorrow where i.m fitting my electric water pump and my boost controller


#376761 Supercharger Boost Control

Posted by DanE on 06 September 2017 - 05:31 PM

Started a new project today to try and tame the boost when trying to cruise @70mph. The idea is using a Mac 3port solenoid boost controller and a mini vacuum pump. The plan is when I switch to economy map it will switch the valve over so the plenum vac line to bypass valve is closed stopping boost pressure at the same time the mini vacuum pump then pulls the bypass valve open thus stopping boost. Hopefully then I will be able to drive at 70mph without boosting to warp speed all the time... Will update when I have made and fitted it all.


#376692 Kid Racing At Eosb

Posted by DanE on 04 September 2017 - 12:05 PM

It was rather funny.


#376526 2L Blacktop Zetec Turbo

Posted by DanE on 31 August 2017 - 09:01 AM

The end bhp is irrelevant if you boost more than the 11psi it will be an early grave for the zetec. But 240 should be achieved
I.m running arp Conrod bolts

Think about the torques that's where the smiles come from

Oh steamer 243.6 i.ll have you know


#376307 Type 9 Electronic Speedo Sender Cheaper The Burtons And Cbs

Posted by DanE on 24 August 2017 - 07:21 AM

Just bought one off burton power For £43.87 ! when it turned up it was in a Cambiare box with a part number of VE363408 with a http://www.burtonpower.comsticker over it.  if you search this you will find it for about £26 every where else, typical burton power really nice mark up...




#376160 Mismatched Gauge Solution

Posted by DanE on 19 August 2017 - 05:12 PM

Spida are crap. can not get mine to work at all. Unless I am being a complete bozo and not reading instructions right!

disagree mine works spot on. Pop round one day maybe I would have more luck setting it up