Donor
Have a question about the donor car? or what you need...
387 topics in this forum
-
As my alloys are too large for the front mudguards im trying to find a set of steelies to put on. What size wheels did the sierra GL have? Nigel has kindly offered to lend me his alloys if i get stuck locally,
-
Hey all I'm currently stripping down a Sierra (1987 2.0i ghia) and everything is off bar the rear brakes/driveshafts/diff. One problem I'm having is that I can't get the rear drums off. They woble but wont budge, even with a thver in between the back plate and the drum. The brake hoses are disconnected and the handbrake has been removed. The haynes manual says to poke a screw driver through the hole in the drum to release the auto adjuster - trouble is there is no hole in the drum! I though about a puller but the largest I can find is 250mm and the drums will need one of about 300mm. Any ideas how to proceed? I don't mind if the drums/pads get damaged in …
-
Advise needed! Can anyone tell me if any of the engine ancillaries of a 2ltr DOHC can be used on a Pinto engine? Also can the engine and gearbox mountings be used? Thanks Mark O'Neill
-
- 3 replies
- 1.2k views
-
-
Hello Does any one know what the size and thread of the nuts required for both the track control arm to the hub and steering rack are? I want to replace my castle nuts with nylocs, have tried various Metric size nuts, 10 and 12 I think but the thread appears to be wrong are they imperial? Or am I best off taking the car to the garage to fit the wire to the castle nuts? Thanks Mike
-
what bits are needed from your donor sierra,engine,gearbox,drive shaft,axle,brakes and what else ?
-
- 17 replies
- 3.5k views
-
-
I'm going to pick up the rear axle assembly off a 2.0 4x4 on sunday, but have to take it off myself and I've gone and "misplaced" the haynes manual somewhere, it's a bit late to tidy the garage tonight so could anybody offer some info as the best way to remove the whole lot (rear beam with diff, driveshafts and disk brakes ), as I'm guessing there will be things like an exhaust in the way on the sierra I didn't build it so didn't have the fun of stripping the donor, how long a job is it? will I need anything other than a socket set and a hammer?
-
- 18 replies
- 3.6k views
-
-
Hi all, I need to get the weight (and dimensions) of a Stainless Steel exhaust manifold. I realize they all vary a bit, but ballpark is fine. Can anyone help me out? TIA. Cheers, -sm
-
Is anyone looking for a good donor vehicle ? See my advert in the For Sale section. thanks JP
-
I am in Thailand and Sierras were never sold in Asia. Is there a similar Mazda mdel that has the necessary interchangable bits? Robert
-
I am considering building a SS in Thailand and in spite of several questions to RHS, have still not recieved an answer regarding what is not included in the kit. One would think that this is a FAQ, and I am at a loss as to why the inability or perhaps unwillingness to answer my question. This is a developing country and one cannot just pop down to the auto shop for essential bits that are not included in the kit, or have RHS rectify any short shipment. Sierras were never sold in Asia so finding bits is impossible. I can only assume from comments from listees and others assume that this is not a Mecanno set, and it is by no means complete. I am OK with this, but ne…
-
As a complete newbie, can anyone please help to get me started on my 2B Plus. The one thing a numpty like me needs from the videos is a build sequence, I watched for nearly an hour on how to assemble two front suspension systems, neither of which I have, (Wish Bones) then on to the boot lids!!!! Having watched all videos several times I can't work out a sequence. I am thinking floor pan, rear suspension, front suspension, engine and gearbox, pedal box and brake servo unit, then steering. How am I doing?? :boohoo:
-
- 33 replies
- 6.1k views
-
-
I have been thinking about my next kit, i have a 2b wishbones with a 2l inj pinto and am currently helping build a westfield X1. When finished i will have space in my workshop for my next kit, i dont know what yet but it will be lighter with more power and a v8 would sound great!! I am looking out for engines but would like some advice on what to buy. Is it right that the sd1 vitesse is best? What about land/range rover? Any tips gratefully recieved Thanks kenton
-
I have bought a S7 (I think) that is damaged and need some parts.The car is monocoque construction with double wishbone front and live axle rear. The parts I need are Nosecone,cycle wings which i,m thinking I will have to get from Robin Hood?. Also one of the rear coil springs is missing, can anyone tell me what car this is off?. I also need a streering rack and one of the lower front wishbones is damaged needing replacing. I would be grateful of any help and advice you could give. I will try and upload some pics.
-
- 5 replies
- 1.5k views
-
-
Hi all, First of all, i believe the wishbones on the lightweight are pretty much the same the ones on the 2b-plus/superspec, so this question is fairly generic...can someone confirm this (that they are the same)?? I have a set of sierra/xr4ti brake/hub assemblies, but i want to switch to a MUCH lighter more performant solution. eg, something like (capri upright and brake): http://www.stuart-taylor.co.uk/images/products/003.jpg The question is "what upright/hub/brake assembly can be used w/ the wishbones?? Just sierra? Cortina? Capri? ????" I have heard that the sierra uprights have geometry problems, and it is better to go w/ the coritina uprights (th…
-
I built my robin hood out of a sierra sapphire 2ltr,just wondered if anyone knows if i could put a limited slip diff in it without using drive shafts or would i need to put limited slip diff drive shafts in? Thanks bernie
-
Hi all, Well, i have begun picking up my parts, tho i don't really know what to get, since i don't know what comes in the kit (since i don't have it, and i don't trust RH). Input from the lightweighters that have their kits would be great!!! So, i got the duratec i4 (that i have been spouting off about), 2 racing seats (ya, i know it comes w/ seats), all 4 merkur (sierra) brakes and hubs, 2 rear half shafts, and a t9 tranny (and drive shaft). I am still (desperately) trying to find a xr4x4 LSD!!!! What else do i need? How good is that "maxcool radiator"? If i am going to race my l/w, is it beefy enough? Thanks for help, and feel free to add your own want…
-
I'm looking for Sierra front uprights with disc brakes included in good nick,but not too expensive,and a rear Sierra axle with brakes and all the bits to make the car(a Robin Hood S7)into a rolling chassis.Any offers considered,or help about where to look/buy would be great.Many thanks in advance....
-
Hi all, I was down at the scrap yard the other day and saw a diff hanging off a 4x4 sierra. Someone has alreay taken the discs and calipers. Are all 4x4 seirra's blessed with a LSD? If they are.... will it just bolt into my existing drum brake rear axle? Im sure this has been covered before but i can't find the thread. Cheers Jon
-
well after a great day at brands,the strip started today with bill having the front hubs and the dash clocks bob tucker is having the rear axle less the diff so who wants what else
-
I am a newbie on here,and have just purchased a second hand Robin Hood S7 off someone.It’s in fairly good nick,but not a rolling chassis,which I intend to make it asap.Does anyone know detailed information on this chassis,and what donor vehicle is needed(eg.rear axle and front uprights,suspension etc)and whether this can all be taken off in one piece?Any help would be very much appreciated!
-
My donor car was delivered yesterday... Some specs for those interested... 77,000 mile (genuine) Sierra Saphire Cosworth with all receipts Stage 2 head, cams, stock ECU (stage 2 was sold prior to my intervention) Group A Head Gasket and Head Studs, Full engine and turbo overhaul at 73,000 miles. 1990 so no cat. All the hoses are intact, the pic was taken just after he removed all the nice samco bits and K&N... Runs nice and quiet, blows no smoke, but needs matching to current ecu Fitted with Clifford 50 Alarm Previously Owned by a 20 yr old who paid £6,000 and killed shell/bodywork in 16 days! LOL A bargain at £1950 Muwahahahahahahaha
-
i think im right,but just checking,does this car have a lsd,the guy has ended the auction for me,and im collecting on saturday e-bay link
-
The engine from the donor is a mess, old pinto so not 205, about every seal and gasket has leaked oil or water and to add to the problems, it's seazed..So can i change the engine on the donor V5? The donor is not on SORN as it was purchased before the regulations ( says you don't need to on the SORN form ) So can i just change the engine number on the V5 or do i need to Sorn it first. Also does it affect the emmisions alowed fitting a newer pinto?
-
- 7 replies
- 1.6k views
-
-
Hi all, A friend knows of a granada 2.9 cosworth v6 Lreg thats going to be scrapped as its an mot failure, i was wondering if the diff was a lsd in which case i would have the whole rear end including disc brakes for my 2b. Is it worth the time/effort? thanks kenton
-
Hi, I'm new to the site and will be joining the club as i'm going to be building a 2b. My question is i know of an Xr4x4 about to be scrapped can i use any parts of it, I know the gearbox and engine are no good but what about the rear diff and subframe assy and what about front stub axle assy's and steering components. I like the idea of rear discs and lsd which i think the 4x4 has. Any help would be great. Cheers Gogsie